模具常用英语! 2008 年 09 月 12 日 星期五 15:56 模具英语句子
  1. XXX!你现在有空吗,我可以问你一些问题吗? Could I ask you some questions if you are free? / Are you free now? May I ask you some questions (a question)?
  2. 请问此产品的面是否为外观面?表面做什么处理?是晒纹/抛光? Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing ?
  3. 请问产品这个面可否加顶针或顶块?产品允许加扁顶针吗? Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?
  4. 这个产品的柱位我们打算做司筒.(或镶针)可以吗? Can we add ejector sleeves or ejector pins in the boss of this part?
  5. 产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗? There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK?
  6. 产品里面的这个位置我们打算做斜顶或内行位,有问题吗? We will make the lifter and (inner) slider in this position, will that be a problem?
  7. 你提供的 2D 产品图与 3D 产品图不一致,请问以哪一个图面为准? The 2D and 3D drawing you provided is not the same, can you tell me which one is correct?
  8. 你提供的 3D 产品图有的地方没有出模角,有的地方胶位太厚,有的地方胶位太溥,这 些产品问题我们可以自己修改吗?修改后会给交给你确认. There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it.
  9. 按你们提供的缩水率千分之五,这个模具的尺寸已经做到了模具图面要求.但注塑出 来的产品不符合你们的产品图.请确认你们的材料的缩水率是否正确? According to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right?
  10. 产品的这个位置太小,导致模具钢料太溥,能够加宽这个位置吗? This position is too small and will make the steel material here too thin, can we widen it here?
  11.斜顶与后面的柱位空间太小, 斜顶在运动时会干涉到柱子, 能移动这个柱子的位置吗?
The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss.
  12. 这个筋骨位胶厚太溥,而且高度偏高,注塑时很难填充这个筋位,可以增加这个筋骨 位的厚度吗? The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you increase the thickness of this rib?
  13. 你是想将此筋骨位的高度加高/减低吗?加胶的位置我们将用铜公放电加深.但减胶 的位置有两种做 法,1,做镶件;2,烧焊;因为镶件的底部有运水,我们简单的做法是烧 焊处理,你可以接受吗? Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease:
  1. Make inserts;2 Welding, because there is water in the bottom of the insert, is that OK?
  14. 这个样板的筋骨位底部烧焦,是因为排气不良,我们可以在筋骨位的中间增加一个镶 件. This sample has been burned in the bottom because the venting is not good, we can add an insert in the middle of the rib.
  15. 重做镶件大约需要 5-6 天时间,你能接受吗? It will take about 5 or 6 days to redo the insert, is that OK?
  16. 产品的这个面我们已经做了晒纹处理, 如果需要加胶, 这个面我们需要重新外发晒纹. 可能需要几天的时间.所以我们直接以铜公放电的火花纹取代你要求的纹路,你可以接受 吗? We have made the texture on this side, if we add material, it will take some days to remake the texture by out-resourcing, so we suggest using the texture by EDM instead, is that OK?
  17. 模具是用公制/英制的配件?需要备用件吗? Is this mold dimension measured in inches or meters? Does it need spare parts?
  18. 模具上铭牌上的刻字内容是由你们提供吗?你们什么时候可以这些刻字资料. Will you provide the engraving content of the plate of this mold to us? When will you send it?
  19. 可否提供此模具生产时,注塑机的型号及相关资料.如:啤机大小,呵林柱尺寸,顶 棍孔尺寸等 Can you provide the type of injection machine and other related information of this mold to us? Such as the boss dimension, the hole's dimension of the ejector pin and the size of the injection machine and so on.
  20. 这个问题我需要同其它同事商议会再答复你.
I need to discuss this problem with the other colleagues and then I will reply back to you.
  21. 我们将尽力达成你的计划,如有异常,会及时通知你. We will try our best to complete your plan, if there are any complications, we will notify you immediately.
  22.这个产品的长度为 3
  30.12MM,宽度为
  78.96MM,高度为 45MM.胶厚为 2MM,重量为
  70.63g, 试模注塑机型号为 250 吨,胶料颜色为黑色,产品外表面晒纹处理,内表面为抛光.需要日期 章,环保章,材料章.前后模用 2344 氮硬,斜顶和行位座用 738H,以上模具信息正确吗? 请确认! "The length of this part is 3
  30.12MM, Width is
  78.96MM, height is 45MM, thickness is 2MM, weight is
  70.63g, the injection machine is 250T, the material is black, the outside of the part has texture, inner side needs polishing, and it also needs a date and recycle stamp ,the core & cavity is 2344 nitridng, the lifter and slider shelf is 738H. Please check the information above!"
  23. 现在到了吃午钣的时间,我们下午再继续好吗? It is time to have lunch, let's discuss this project later this afternoon?
  24.和滑块干涉的倒勾请加料填平至滑块可以顺利滑动 (The undercut area interferes with the slide block and needs to be filled with material to help the slider move smoothly.)
  25. 加肉太多 (The thickness added is too thick.)

  26. 加肉面积太大 (The thickening area is too wide.)
  27.GATE 位置移位 ( The gate position is moved.)
  28. 滑块拆的位置 (The split line of slide block or the area of slide.)
  29. 此处有尖角,填充困难 (It is hard to fill this area due to the sharp feature.)
  30. 此处钢材太薄,强度不足而且不容易冷却 (The strength of this area is too weak and it is hard to cool because the steel is too thin.)
  31. 圆柱特徵要有一半圆不可以拆在滑块上,以免粘滑块造成拉白,拉断 (We avoid designing the semicircle of the cylinder on the slide block because it will be pulled apart or cause drag marks.)
  32. 此处做斜销在作动时会削到成品肉厚 (The part will be damaged if we make the lifter in this area.)
  33. 这个面是装配面,不能加料
(This is a critical surface where we cannot add additional material.)
  34. 此处料位太厚,会有缩水,建议减料改善 (Because of the shrinkage of the thickness, we suggest reducing some wall thickness to improve it.)
  35. 此面是不是外观面,此处做滑块的话会有夹线,是否可以接受 "(Please confirm whether it is a critical surface or not. Also, confirm whether it is acceptable to have a slide split line if we have a slide in this area. )"
  36. 此处有倒勾,能否减料,使公母模靠破,不做滑块和斜销 "(Please confirm whether we can reduce material to the area where we have an undercut as indicated to have shut off on cavity side. No slide block and lifter will be made. )"
  37. 请尽快确认这种拆模方式和结构,否则会影响模期 (Please confirm the issues of Parting line, Gate position...Etc. as soon as possible; otherwise, the lead-time will be extended.)
  38. 此面是否有特殊要求,能否有顶针印 (Please confirm whether it is a critical surface or not and if we can have E.J. pin marks on it.)
  39. P.L 面开在此处,模具上会有尖角和刀口,对模具寿命有影响 (There are sharp edges if we set the parting line here, It will reduce the tool life)
  40. 加大拔模角, 以便脱模顺利 the tool.) We suggest enlarging the draft angle to help release

  41. GATE 做在此处的话有两个缺点:
  1.盖子打开时可以看到 GATE 的修剪部位;
  2.两个斜 销在同一侧,顶出也不是很平衡. (There are two problems if the gate is to be designed in this area: a). It is easy to see the gate mark when you open the cap. b). The ejectors are unbalanced when two lifters are on the same side)
  42. GATE 做在此处的话.盖子打开后看不到 GATE 的修剪部位 (The gate mark is not visible if the gate position is designed like this.)
  43. 如果 GATE 一定要做在你们指定的位置的话, 那还不如做在这一侧, 这样的话还可以减 小这个位置的缩水 "(If you insist that the gate position has to be like the original design, then we would further recommend to have it to the area indicated so it can avoid a shrink problem in this area.)"

  44. 在此处 GATE 做潜顶针的话,背后的外观面会有冲料痕,而且成品又是黑色的,会最明 显 (If the design of the gate has to be a sub. Gate, then the back surface of the part will have serious flow marks due to the black color.)
  22. P.L 开在此处不合理,模具加工困难,P.L 应改为和图示的一样 "(This area is not suitable to have a Parting line because the tool will become more complicated; therefore, we recommend to have the Parting line as indicated.)"
  45.产品粘母模的机会很大,能否在公模加倒勾,拉料顶针或者公模保留 E.D.M 纹,开模 时使成品留在公模一侧 "(There is possible sticking on cavity; therefore, please confirm whether it can make undercuts, snatch pins or leave coarse E.D.M. on the core to snatch the part on) "
  46.此处料厚段差很大,成品表面会有应力痕,是否接受 (Please confirm whether it is acceptable to have stress lines on the surface because the thickness is not equal.)
  47. 请注明何处为外观面,能否提供 2D 图和注意事项 (Please advise where the critical surface is. Please also provide us a 2D drawing with critical dimensions. )
  48. 红色所示处是有问题的地方,请特别注意 (Please note the red highlights because those areas have problems.)
  49. 成品设计此处有问题,建议如下图所示修改 (We would suggest using the attached part design as the current design has problems.)
  50. 此处改为一个球形的凹槽 (We suggest modifying it as a globe recess.)

  51. 圆柱特征要有一半不可以拆在滑块里,以防拉断 (this issue is the same as no.
  31)
  52. 此处大滑块上走小滑块,小滑块要先退,大滑块要做延迟 (The inside small slide block will recede first and the parent slide block have to postpone sliding.)
  53. 滑块要用液压油缸抽芯以保证开合模顺序 (The slide pins will use an oil cylinder to assure that the process is in proper order.)
  54. 这个面有装配,加料的话装配时会顶住,如图所示 "(We cannot add material to this surface because it will intervene between the two
parts when it is assembled. Please see the sketch attached. )"
  55. 可降低斜销面,增加成品些许肉厚来做变化 (To descend the surface of lifter in order to thicken the part.)
  56. 一半做斜销,一半做自然 (One half side will have the lifter and the other half will be solid/nature.)
  57. 此处两个柱子重叠,有倒勾,不能做自然,要做 SLIDE "(These two bosses are overlapping with undercut therefore it can not be made as solid. We suggest making it with a slide block.)"
  58. 此处强迫顶出 (This area needs force ejection.)
  59. 公模两段开模,这个地方先退 (Here will be a double ejection for forward and receding.)
  60. 此处做镶件会有夹线,能否接受 Please confirm whether it is acceptable that there will be a split line here.)
  61. 此面公母模 1 度靠破,会有段差,可否接受 (Please confirm whether it is ok to have mismatch to the area where there is 1 degree of shut off in Core / Cavity side.)
  62. 这个尺寸能否加大 (Please confirm whether we can enlarge this dimension.)
  63. 此处加一个凹槽,胶片的弹出效果会更好一些,试模后看装配的效果再做修正 "(It will affect the elastic of the film better if we add a recess. See how it will affect the assembly parts, and then make your decision.)"
  64. 此处有倒勾,建议将剖面线所示部位 CUT 即可避免此处的倒勾 (There is an undercut here, we suggest cutting out the indicated part as it highlighted to avoid an undercut.)
  65. 成型后 SUB GATE 要修平 (The gate (sub gate) needs to be trimmed evenly after being moulded.)
  66. 此处倒勾先垂直顶出,之后再手动取出 (This area of the undercut needs to be ejected vertically, then taken out manually.)
  67. 这两个面都有滑块,GATE 改在此处改不到 (The gate is not suitable in this area because there are two sliding blocks sealing off this area.)
  68. 此处加做一个旋转 GATE,射出时方便调整成品的品质 (We would suggest placing a runner shut-off insert to adjust the volume of part filling.)

  69. 此倒勾在滑块上强迫脱模,倒勾是否可以减小到
  0.6 (This undercut will be force ejected out, Please confirm whether it can be reduced to
  0.6 mm.)
  70. 此柱子无法脱模,请确认是否是在转图时错位,能否提供客
 

相关内容

最常用英语对话口语

   Any day will do? 哪一天都可以? Any messages for me? 有我的留言吗? Are you by yourself? 你一个人来吗? All right with you? 你没有问题吧? Are you free tomorrow? 明天有空吗? Are you kidding me? 你在跟我开玩笑吧? As soon as possible! 尽可能快! Back in a moment! 马上回来! Believe it or not! 信不信由你! B ...

英语口语 谈论股票常用英语口语对话

   英语口语 谈论股票常用英语口语对话 英语口语 谈论股票常用英语口语对话 听说过吗?躺在床上能和外教一对一练英语口语!适合职场中的你! 听说过吗?躺在床上能和外教一对一练英语口语!适合职场中的你! 免费体验史上最牛英语口语学习, 免费体验史上最牛英语口语学习,太平洋英语 www.pacificenglish.cn 股市最红火的时候几乎是全民皆股,可自从去年调整印花税以来,股市一直是动荡不安,被 套的股民数不胜数。他们见面最常聊的就是“你的股票怎么样了”? Kelly: So, Jim, how ...

结帐常用英语口语对话Checking Out

   结帐常用英语口语对话 Checking Out 不管是吃饭还是住酒店,我们都要 check out 也就是结账和退房. 我们特别整理了一些关于结账的英语口语对话! 1.I'd like to pay my bill now. 我想现在结账. 2.Your name and room number,please? 请问您的姓名和房间号码? 3.Have you used any hotel services this morning? 请问您今天早晨是否用过旅馆内的服务设施? 4.Four n ...

常用英语对话

   Mario 一 简单问候: Hola!您好 Hey!嗨 Soy yo!是我 Buenos días!早上好/上午好 Buenas tardes!下午好 Buenas noches!晚上好/晚安 Cuánto tiempo sin verte. 好久不见了 Cuántos a?s hace que no te veía.几年不见了 Hola,hace mucho tiempo que no te veo.好长时间不见了 Encantado de volver averte.很高兴再见到你 Qu ...

实用英语对话

   初次见面的自我介绍 ① May introduce myself? ② Hello,I am Tom. ③ Excuse me,I don’t think we have met.My name is Tom. ④ How do you do?I am Tom. ⑤ First,Let me introduce myself.I am Tom,Production Manager. 介绍后的回答 ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ I am glad to meet you. Nice me ...

常用英语口语对话

   What are you trying to say?(你到底想说什么?) Don't be silly.(别胡闹了。) How strong are your glasses?(你近视多少度?) Just because.(没有别的原因。) It isn't the way I hoped it would be.(这不是我所盼望的。) You will never guess.(你永远猜不到。) No one could do anything about it.(众人对此束手无措。) ...

英语学习_日常英语对话_必备

   弃我去者, 弃我去者,昨日之日不可留 乱我心者, 乱我心者,今日之日多烦忧 一、 Greetings 问候语 你好! 1. Hello! / Hi! 你好! 2. Good morning / afternoon / evening! 早晨(下午/晚上)好! 早晨(下午 晚上 晚上) 我是凯西?金 3. I\'m Kathy King. 我是凯西 金。 4. Are you Peter Smith? 你是彼得 史密斯吗? 你是彼得?史密斯吗? 史密斯吗 5. Yes, I am. / No, ...

英语对话

   a: Mary looks miserable today,doesn't she? 玛丽看上去愁眉不展。 b:yes,she does.She flunked physics and barely passed math. 是呀,他物理没通过,数学也差点儿没及格。 a:oh,sorry to hear that.physics is aways a pain in the neck. 哦,真遗憾。物理一直让我头痛。 b:we r in the same boat.physics is no ...

英语对话

   对话一:兴趣 A: well, Xiao,I already know that you like watching movies.What other kinds of things are you Li interested in ? B:You know in university,we have a lot of free time.So I would like to learn something that I'm interested in but had no time to ...

英语对话

   中英文\?q 10/11/05 Have you got used to the weather here? 你已}??c?里的天气了U? I think it’s going to be a nice day. 我想明天g是P好天气. What’s the weather like out? 外面天气如何? SALUTATION UO候 Haven’t seen you for a long time. 好久不??了. Pleased to meet you again. 很高?再??到 ...

热门内容

必背常用英语单词

   一、一个星期七天 Sunday Monday Tuesday Wednesday Thursday Friday Saturday 二、一年十二个月 January February March April May June July August September October November December 三、一年四季 1. spring 2. summer 3. autumn 4. winter 四、容易拼写错的数字 1. eighth 第 八 2. ninth 第 九 3. ...

2005年普通高等学校招生全国统一考试??英语(江苏卷)

   本资料来源于大家网高考英语论坛 http://club.topsage.com/forum-136-1.htm 2005 年普通高等学校招生全国统一考试(江苏卷) 英 语 YCYYCY 本试卷分第一卷(选择题)和第二卷(非选择题)两部分。第一卷考试结束后,将本试 卷和答题卡一并交回。考试时间 120 分钟。 第一卷(选择题共 115 分) 意事项注: 1.作答第一卷前,请考生务必将自己的姓名、考试证号用书写黑色字迹的 0.5 毫米的签 字笔填写在答题卡上,并认真核对监考员所粘贴的条形码上的姓 ...

大学英语六级大纲词汇

   大学英语六级大纲词汇 大学英语六级大纲词汇 六级大纲 2008?08--28 2008?08--28 -abbreviation=n.节略, 缩写,缩短 abide=vt.遵守 vt.忍受 abolish=vt.废除,取消 absent=a.不在意的 absorption=n.吸收;专注 abstract=a.理论上的 n.抽象 absurd=a.不合理的,荒唐的 abundance=n.丰富,充裕 accessory=n.同谋 a.附属的 accord=n.调和,符合;协议 acknowl ...

2010年6月份英语六级真题及答案

   本资料由学生范文网 为您收集整理。 本资料由学生范文网(http://www.xsfanwen.com)为您收集整理。 学生范文网 为您收集整理 月英语六级真题 2010 年 6 月英语六级真题 Part I Writing (30 minutes) 注意: 注意:此部分试题在答题卡 1 上。 Directions: For this part, you are allowed 30 minutes to write a short essay on the topic of Due Att ...

六年级英语第一次月考试卷

   六年级英语春学期第一次月考试卷 题号 得分 一 二 三 四 五 六 七 八 总分 听力部分(40 分) 一、 听音圈出你所听到的单词(12 分) 1、game 2. bought 3、clerk 4、head 5、baby 6、team some taught snack hard body teeth name thought score hand boy teacher gym light soccer hurt Dad teach 二、 听音选出正确的答语。 (10 分) ( )1、A ...